Seals are the basic components of hydraulic, pump valves, reducers, and chemical equipment. Their core mission is to prevent medium leakage and prevent dust, water vapor, and impurities from entering the interior of the equipment. According to whether there is relative motion between the sealing mating surfaces, the sealing system is divided intoStatic seal和Dynamic sealTwo major categories; Dynamic seals are divided into reciprocating seals andRotating seal (rotating dynamic seal)In many engineering scenarios, people are accustomed to discussing static seals, dynamic seals, and rotary seals in parallel, clarifying their roles, principles, and applicable boundaries, which is the basis for seal selection and fault diagnosis.
1、 Static seal: a sealing barrier on the static joint surface
Static sealing is applied after assembly is completed,There is no relative motion between the two sealing mating surfacesThe connection position relies on bolt clamping force to cause elastic deformation of the seal, filling the micro concave convex gaps of the metal joint surface and blocking the medium flow channel. Flange connections, pump body end caps, oil pan mating surfaces, and pipe joints are all typical static sealing conditions.
The core function of static sealing is to achieve long-term sealing on a stationary fixed joint surface, isolating oil, water, gas, and chemical media. It does not undertake the task of friction or following motion, and the design focus is on the uniformity of compression, material temperature and medium resistance, and creep resistance.
Common static sealing components include O-rings, various flat gaskets, metal wound gaskets, sealants, raw tape, etc. O-ring is the most versatile static seal, which relies on pre compression to achieve sealing. When the pressure is high, it needs to be matched with a retaining ring to prevent extrusion damage; Metal wrapped gaskets are commonly used for high-temperature and high-pressure steam and chemical flanges; Rubber pads and PTFE pads are suitable for low-pressure and corrosive working conditions.
The failure of static seals is mostly related to the clamping force: uneven torque of bolts, deformation of flange surfaces, and thermal expansion and contraction caused by long-term temperature cycling can all cause a decrease in clamping force and leakage; Long term stress relaxation and decreased rebound ability of rubber and gaskets under pressure are also common causes of leakage. Overall, the static sealing structure is simple, with no friction loss and low cost. However, it is generally recommended to replace gasket parts after disassembly and assembly, as the stability of working conditions with large pressure and temperature fluctuations is relatively weak.
2、 Dynamic sealing: sealing scheme between moving parts
When there is continuous relative motion between the parts on both sides of the seal, dynamic sealing is required. Dynamic sealing not only needs to achieve sealing, but also allows continuous movement of components. It naturally has a contradiction: sealing needs to be tightly fitted, while movement can bring friction, heat, and wear. Therefore, the requirements for material, lubrication, and processing accuracy of dynamic sealing are much higher than those of static sealing.
Dynamic seals can be divided into two categories based on their movement form:Reciprocating seal与rotary sealThe reciprocating seal corresponds to linear reciprocating motion, and the typical representative is the seal between the piston and piston rod of the oil cylinder and cylinder. Commonly used seals include Y-shaped rings, seals, gaskets, V-shaped combination seals, and dust seals. Most of these lip seals have self tightening characteristics, where the higher the medium pressure, the tighter the lip fit, making them suitable for linear reciprocating motion in hydraulic systems; The dust ring is installed on the outermost side of the oil cylinder to scrape off the mud and sand on the surface of the piston rod, protect the main seal, and also belong to the dynamic seal.
The core function of dynamic sealing is to continuously maintain the seal under relative motion, prevent high-pressure medium from moving and leaking, and protect the sealing substrate from impurity wear. The dynamic seal must rely on a very thin lubricating film to reduce friction, and dry friction can quickly burn and fail the seal. The upper limits of temperature and pressure allowed for dynamic sealing using the same sealing material should be lower than those for static sealing conditions.
3、 Rotating seal: a specialized dynamic seal for rotating shafts
Rotary seal is a branch of dynamic seal, specifically used forThe shaft continues to rotate around the axisThe scene is widely used for the shaft position of reducers, motors, oil pumps, centrifugal pumps, and chemical pumps. Its sealing object is the gap between the rotating shaft and the fixed housing, which is one of the most vulnerable locations for oil leakage in the equipment.
According to the sealing method, rotary seals are divided into contact and non-contact types. The most common contact type is the skeleton oil seal, which relies on a built-in spring to tightly hold the sealing lip on the shaft surface, forming a narrow sealing band. When in use, the sealing lip must face the oil side, and once installed backwards, it will quickly fail; Mechanical seal is a high-end rotary seal for pump equipment, which relies on the contact between the end faces of the moving and stationary rings to form a seal. The end faces are lubricated by a liquid film of the medium, and can withstand high pressure, high speed, and strong corrosive media. It is commonly used in chemical pumps and sewage pumps. Non contact types include labyrinth seals, spiral seals, magnetic fluid seals, etc. The sealing surfaces do not directly contact each other and rely on throttling and pressure reduction to achieve sealing. There is almost no wear and tear, and the service life is long. However, most of them allow for trace leakage and are suitable for high-speed fans, compressors, and vacuum equipment.
The core difficulty of rotary seals lies in the continuous friction around the circumference, as well as shaft runout, eccentricity, surface scratches, and excessive linear velocity, which can cause unilateral wear and carbonization of the lip, making it a high-risk category for on-site failures.
4、 Summary of the core differences among the three
The most fundamental criterion for determining the type of seal isIs there any relative motion and form of motion on the sealing mating surface。
Static sealing has no relative motion and relies on external compression force for sealing, with no friction or wear. The selection focuses on the medium, temperature, and compression method; Dynamic seals have relative motion and need to balance sealing and wear resistance, which can be divided into two directions: linear reciprocating and rotational; Rotary seal is a subclass of dynamic seal, specifically referring to shaft rotation conditions. Continuous circumferential friction is its biggest feature that distinguishes it from reciprocating seals.
From the perspective of usage scenarios, static seals are preferred for flanges, end caps, and fixed joints; The linear motion of the oil cylinder and cylinder piston rod adopts reciprocating seals; When the gearbox, pump, and motor shaft rotate, a rotary seal is selected. Many seals have the ability to adapt to multiple scenarios, such as O-rings that can be used for static sealing or low-speed reciprocating sealing. However, they are not recommended for high-speed rotating conditions as friction heating can quickly damage the seal ring.
In industrial maintenance and selection, distinguishing the sealing type is necessary to match the corresponding sealing structure, groove size, material standards, reduce leakage failures, and extend equipment service life.

